Make Your Prints Fit Any Frame…

Posted by: In: Other, Techniques 23 Jan 2011 Comments: 17 Tags: , , ,

What I’m going to be demonstrating – Blue Peter style, here, is how to make a mount for your image. The great thing about making your own mount, is that you can fit any picture into any frame. Just alter the size of the mount. For a few pounds at a charity shop/boot sale, there are some great frame bargains to be had, and you can have a really professional looking mounted image for very little cost once you have the right tools. Once you’ve done a couple of these, it’s also a very quick and easy thing to do. You also get to play with a knife.

Yes. You’re going to be playing with sharp pointy things, so if you’re irresponsible, get an adult to help.

First up, the tools:

You’ll need:-

– A sharp stanley knife or something that will cut through mountboard. These can be obtained at pretty much any hardware store for a few pounds.

– A cutting mat. This will prevent your knife from gouging holes in the table. Amazon sell these, as will any large stationary shop. I’d get one as big as you can afford.

– A tough straight edge with a handle.

– A 45 degree mount cutter. This is the expensive bit. I use a Logan mount cutter as they seem to be the best. You may wish to consider a cheaper alternative, but if you’re going to be doing a few frames (and as a photographer, what better way to display your photos than on the wall at home!) it’s worth the investment of a decent cutter.

– Some mount board. Comes in all shapes and sizes, but it’s worth getting good quality boards.

– Mounting pins. These are small triangles of steel used to hold the backing board in place.

– Tape. I use masking tape, but sellotape works just as well. To remind you, this is not a “how to proudly display your fine art prints” – as the acid in the tape will damage the photo eventually (mine are still on the wall after 5 years with no sign of decay) but unless you’re saving your prints for your grandchildren’s grandchildren, masking tape will do!

– A frame. Go to the charity shop and pick up a frame. Any frame. As long as it’s bigger than your print. Just make sure the glass is intact, and there’s a backing board. You don’t want to be hacking up hardboard, or cutting glass to size. Or you could get reasonably cheap frames from Ikea.

– A print. One of your precious photos.

– The dining table. Or its equivalent. Don’t start this at lunchtime!

tools for mounting a photograph

1. Preparing the frame

Take your frame from the charity shop and turn it face down. If you’re lucky, it’ll have bendy bits of metal allowing you to get the picture out with ease. If you’re unlucky, you’ll need a pair of pliers to pull out the old mounting pins. Watch your knuckles, and your language! Pull off excess tape until you’re bored.

Take out the glass. Carefully. Give it a good clean with vinegar and newspaper. Or use a glass cleaner…

Have a look at the frame. If it’s dented, scratched, chipped, or the wrong colour, then it might need a touch up job. Take it outside and do what you want with it. I’ve taken some frames as they are, but others benefit from a coat of paint. You may even want to go the extra mile and sand it right down to the wood and varnish it. It’s up to you. If you got a good quality frame, you won’t need to touch it, but if it was 50p from a car boot and is chipped and cracked, then a thick coat of black paint, followed by a light sprinkling of silver makes a good surround for a monochrome image.

2. Cutting the mount.

Now for the tricky bit. You can take as much time as you want with this, and that will dictate how the finished product will look. In all honesty, you don’t need to be that precise.

Make sure your cutting mat is clean. Nothing worse than making a lovely mount only to find it’s got black smudges of dirt on the front that you can’t shift without sandpaper.

Examine your mountboard. Decide which is the “good” side – i.e. the side that will be facing your audience. Place the good side FACE DOWN on the cutting mat. Write “bad side” in pencil on the back, just so you don’t start drawing all over the wrong side. If you’re not an idiot, like I am, skip this step.

If you’re lucky, you’ll have a piece of mountboard the same size as your frame. I’m never that lucky, so the first job is to cut the mountboard to the right size. You can do this one of two ways. Either measure the backing board, and cut the square out, or draw round the backing board. I prefer the latter. I know the backing board fits the frame, and I don’t want to be trimming bits off my lovely mount before I’m done.

It’s really important that you keep the mountboard square – this is where the lines on the cutting mat come in handy.

Put a lot of pressure on the ruler. That’s why you bought one with a handle. Mountboard is quite tough, and you need to cut through it with a sharp blade. If it’s not sharp, you’ll make a mess if you don’t cut through it on that first pass. Practice cutting scrap mountboard first to get an idea of how much pressure you need to apply.

Now, you have a piece of mountboard that fits the frame. All you need to do now is cut out the hole for your print.

This is done in a few simple steps.

3. Get the picture central on the horizontal plane.

The picture needs to be in the middle of your frame. To ensure this is done:

– Measure the width of your mountboard. (m)

– Measure the width of your image. (i)

– Calculate “x” where x=(m-i)/2.

centralising the photograph on the mount

As you can see from this example, the mountboard is 14″ wide, and the image is a 10×8, so 10-14 = 4. /2 = 2″ gap at either edge.

– Measure in from the left hand edge of the board at the top, “x” and make a mark.

– Measure in from the left hand edge of the board at the bottom, “x” and make a mark.

– Draw a line joining them up.

– Measure in from the right hand edge of the board at the top, “x” and make a mark.

– Measure in from the right hand edge of the board at the bottom, “x” and make a mark.

– Draw a line joining them up.

You should now have two vertical tramlines across the back of your mountboard.

vertical tramlines for horizontal positioning of the photo

You can see the marking points, as well as the lines defining the inside edge of the frame

4. Get the picture wherever you want it on the vertical plane.

I like to have my image towards the top of the frame, so I work on a 2:1 ratio. There’s nothing stopping you putting it in the middle though. Personal taste is all!

getting the photograph central on the vertical plane

Get it vertically central

Not so simple this one. The height of the board is just over 10″ whilst the print is 8. I went for a 1″ gap at the top, with the remainder at the bottom

– Measure the height of your mountboard. (m)

– Measure the height of your image. (i)

– Calculate “x” where x=(m-i)

*Example* Mountboard is 20in high. Image is 8in high. x = (20-8), or 12

– To put your image in the middle, just divide by 2 as you did above. x = 6

– To use the 2:1 ratio divide by 3 to find x. The gap at the top, is x (4), whilst the gap at the bottom is 2x (8)

– Another alternative is to have the same gap at the top as you have at the sides. Using this example, x would be 2.5in at the top and (12-2.5) 9.5 inches at the bottom.

– Measure in from the top of the board on the left edge, “x” and make a mark.

– Measure in from the top of the board on the right edge, “x” and make a mark.

– Draw a line joining them up.

illustrated image of inch measures on the mountboard

With an inch gap at the top, then I measured down 7.25″. This allowed for overlap to stick the image to the mountboard, and the fact that the crop of the image left a couple of white bands at the top and bottom of the image

– Measure in from the bottom of the board on the left edge, “x” (or 2x if you’re using the 2:1 ratio) and make a mark.

– Measure in from the bottom of the board on the right edge, “x” and make a mark.

– Draw a line joining them up.

You should now have a “box” drawn on the back of your mountboard, and if you’re like me, there’ll be some sums on there too. The technical part is over. You can turn the calculator off now.

photograph of the mount cutting guidelines

5. Cut the mount.

If you mess this up, your mountboard goes in the bin. Take care!

One problem I have with the mount cutter is that it slides like a greased monkey down a pole across the cutting mat. One hefty push and you’ve sliced your mount into bits. To combat this, I ALWAYS rest a bit of scrap mountboard under the cut I’m about to make. The mount cutter then “bites” into the scrap and is much more controllable.

If you’re left handed, reverse these instructions!

– Hold the ruler in your right hand. Offer it up to one of your lines, JUST INSIDE the line. The reason I say “JUST INSIDE”, is because you need to cut a hole thats SMALLER than your print, so that the print will have something to stick to.

how to hold the ruler for the mount cutting process

– “Roll” the ruler down so it’s flat. Don’t let it move. Swap hands so that your left hand is now holding the ruler down.

holding the ruler flat for the mount cut

– The mount cutter should have a white marker. Slide it up against the ruler so that the marker is level with your perpendicular line.

where to position the mount cutter on the board

– Push the thumb-slide down. This will make the first cut. Keeping the slide locked down, slide the mount cutter along your line, tight against the ruler, up to the other intersecting line.

– Release the thumb-slide

– Repeat for the other three lines.

– Lift your mountboard and marvel as a small square the size of your image is left on the cutting mat, or swear as you realise you didn’t go far enough with one stroke, and the “insert” dangles in front of your eyes.

the final cut showing the mount

6. Fix the print to the mount.

– Lay a piece of (masking) tape, sticky side up, on your mat.

– Offer up your print and half-stick it onto the tape.

how to mask up the photograph for mounting

– Offer up your mount and position it over the print.

– Lay the mount onto the print and tape, and press down firmly.

– Flip the mount over, and tape down the other three sides, starting with the side opposite to the one you just did.

the final mounted image

With this being a white print, a black mount works better, but doesn’t show up the lines well for this demonstration. Hence the Blue Peter “here’s one I did earlier” moment.

7. Refit to the frame.

If you’ve got bendy bits, you’re done. Put the glass back, the mounted print, then the backing board, then press the metal clips back into place.

If you need to re-pin the backing board…

– Lay the triangular clip on the backing board.

– Using a pair of pliers, grip the frame and the clip, and push the clip into the wood. I find that masking tape on one jaw of the pliers prevents the frame being damaged.

– Once you’re done, tape it all up again to keep the pins secure.

8. Admire over a cuppa.

the finished mounted photograph in the frame

All finished and done. Bought this frame today from a charity shop for £3.99

This really is quite simple, and means that you don’t need to crop your images to certain dimensions to fit into shop bought frames. It’s also a great way to present your images relatively cheaply.

Here’s what you need again:

– Knife £5. A lot of art sites sell scalpels for goodly sums of money, but in the end, you’re going to be using this to cut the mountboard to the size of the frame and that’s it. A Stanley knife from the hardware store will do the job just as well. And with a retractable blade, it’s relatively safe too.

– Cutting Mat £10 : I’d recommend a Ryman Cutting Mat Self Healing A2 610x457mm – Color: Green from Amazon. A2 is a nice big size and you’re not continually shuffling it about under your mount. You could go smaller, or cheaper quality, but mine was worth every penny.

– Mountboard £3: Again, Amazon has a shop selling A1 Mountboardat a very reasonable price. A1 will last you a LOT of frames! Art shops do sell mountboard, but generally, prices run to £3-4 for A2 size.

– Mount cutter £22: When I was doing this at college, we had several mount cutters, and the Logan mount cutter was by far the best. It may seem expensive, but it’s an essential tool for cutting the angled mounts that look so good when framed.

– Ruler £5: I spent an age scouring the internet for this, but in the end found it at our local hardware store! Builders use these types of rulers with handles, so they are good and sturdy.

– Tape & mounting pins… peanuts

– Frames: Varies… Personally, I prefer distressed frames from the charity shops for a few pounds here and there. Car Boot sales are an excellent source of frames too, and if you can handle the odd looks as you walk off with an awful image in a frame, knowing you’re going to be binning it when you get home, this is the cheapest option.

As you can see. Once you have your tools, the expense of mounting a print in any frame is minimal. This is just your outlay!

Once you’re proficient, you can cut double mounts, or even cut titles into the space below your image. It’s the same process repeated, just with different measurements for “x”. I find it very therapeutic too, and a nice break from Photoshop. Believe me, the end result is well worth it.

Ian

Comments: 17

  1. Posted by Lisa 14 May 2017 at 10:22 am Reply

    Really clear tutorial on mount cutting. Given me the confidence to try it for myself.

  2. Posted by Pete Mc 30 Apr 2016 at 1:30 pm Reply

    Super helpful and clear. Definitely agree with Jonathan, you should be running the country.

  3. Posted by jonathan 22 Oct 2014 at 7:50 pm Reply

    this is truly the most useful set of instructions i have ever come across on the internet. have you thought about running the country?

  4. Posted by Trudie Callan 10 Oct 2014 at 11:10 am Reply

    Thank you for your excellent tutorial. I have a Logan system and I have just done my first set of prints. You mention that sometimes it does not come away cleanly. Yes this happened to me. have you got any advice what to do if this happens. Is there a tool that is better than the Stanley knife or should you go back in with the Logan cutter? I used the Stanley knife but it was not as neat as it would have been if it had come out first time?
    Many thanks
    Trudie
    NB Not sure what URL is? Hope this reaches you

    • Posted by Ian 23 Nov 2014 at 11:54 pm Reply

      I tend to find careful work with a Stanley knife works better than going back in with the Logan. Your mileage may vary though! Thanks for taking the time to comment!
      Ian.

  5. Posted by Milli 12 Sep 2014 at 2:34 am Reply

    Really great info with a few bits that made me smile, awesome thanks!

  6. Posted by Vince 29 Jul 2014 at 5:04 pm Reply

    Thanks Ian, just about to start this process and your advice is easy to follow. Looking forward to my first mounted photograph!

  7. Posted by Cheri 02 Jan 2014 at 3:54 pm Reply

    This particular blog post, “ShutterCount.co.uk Making your
    own photograph mounts.” was terrific. I am printing out a copy to show my personal good friends.
    Many thanks-Kristen

    • Posted by Ian 05 Jan 2014 at 12:48 am Reply

      That’s great news. Good luck!

  8. Posted by lynne lewis 18 Nov 2013 at 4:20 pm Reply

    I found this really helpful and am about to have a go for the first time! Thanks for your efforts,
    Lynne

    • Posted by Ian 05 Jan 2014 at 12:45 am Reply

      Good luck Lynne! Take a pic and let me know the results!
      Ian.

  9. Posted by Rob 14 Nov 2013 at 8:41 am Reply

    Hi Ian,

    Just what I was looking for! Very informative and well written- many thanks for taking the time to post it.

    All the best, Rob.

  10. Posted by Peter Lewis 03 Aug 2013 at 8:50 pm Reply

    Very very helpful. Thanks very much.

    Have just spent ages looking at YouTube trying to get tips on how to attach the print to the mount ( having done loads before and using weird 90 degree angles to line up on the back) your method looks great.
    Thanks again

    Pete

    • Posted by Ian 06 Aug 2013 at 2:09 pm Reply

      Thanks for taking the time to comment Pete!
      Ian

Leave a Comment!

Your email address will not be published. Required fields are marked *

Related Posts